dimensions in inches and (millimeters) - 542 - do-215ab features for surface mounted application in order to optimize board space low profile package built-in strain relief glass passivated junction excellent clamping capability fast response time: typically less than 1.0ps from 0 volt to bv min. typical i r less than 1 a above 10v high temperature soldering guaranteed: 260 o c / 10 seconds at terminals plastic material used carries underwriters laborator y flammability classification 94v-0 1500 watts peak pulse power capability with a 10 x 1000 us waveform by 0.01% duty cycle mechanical data case: do-215ab molded plastic terminals: solder plated polarity: indicated by cathode band weight: 0.21gram maximum ratings and electrical characteristics rating at 25 o c ambient temperature unless otherwise specified. type number symbol value units p eak p ower d issipation at t a =25 o c, tp=1ms ( n ote 1) p pk minimum 1500 watts power dissipation on intinite heatsink, t a =50 o c p m(av) 6.5 w peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method) (note 2, 3) - unidirectional only i fsm 200 amps thermal resistance junction to ambient air (note 4) r ja 50 o c/w thermal resistance junction to leads r jl 15 o c/w operating and storage temperature range t j , t stg -55 to + 150 o c notes: 1. non-repetitive current pulse per fig. 3 and derated above t a =25 o c per fig. 2. 2. mounted on 8.0mm 2 (.013mm thick) copper pads to each terminal. 3. 8.3ms single half sine-wave or equivalent square wave, duty cycle=4 pulses per minute maximum. 4. mounted on 5.0mm 2 (.013mm thick) land areas. devices for bipolar applications 1. for bidrectional use c or ca suffix f or types smcg 6.8 through types smcg200a. 2. electrical characteristics apply in both directions. smcg series 1500 watts surface mount transient voltage suppressor http://www.luguang.cn mail:lge@luguang.cn
ratings and characteristic curves (smc g series) fig.1- peak pulse power rating curve p , peak pulse power, kw ppm tp, pulse width, sec. non-repetitive pulse waveform shown in fig.3 t = 25 c a o 0.1 s 1s 10 s 100 s 1.0ms 10ms 0.1 1 10 100 fig.3- pulse waveform clamping power peak pulse current -% t, time, ms td tr = 10 sec pulse width (td) is defined as the point where the peak current decays to 50% of i ppm peak value i ppm half value - i ppm 2 10/1000 sec. waveform as defined by r.e.a. 0 1.0 2.0 3.0 4.0 0 50 100 150 fig.2- pulse derating curve peak pulse power (p ) or current (i ) pp ppm ta, ambient temperature. ( c) o derating in percentage. % 0 25 50 75 100 125 150 175 200 0 50 100 150 200 fig.5- typical junction capacitance unidirectional cj, junction capacitance. (pf) v( ), breakdown voltage. volts br unidirectional bidirectiona v=0 r tj = 25 c f=1.0mhz vsig=50mvp-p o v -rated stand-off voltage r 1 10 100 200 10 100 1000 10000 fig.4- maximum non-repetitive forward surge current unidirectional only number of cycles at 60hz i , peak forward surge current , fsm amperes 8.3ms single half sine wave jedec method tj=tj max. 1 10 100 10 100 200 version: b07 smcg series 1500 watts surface mount transient voltage suppressor http://www.luguang.cn mail:lge@luguang.cn
electrical characteristics (ta=25 o c unless otherwise noted) breakdown voltage stand-off maximum maximum maximum maximum general v br test current voltage reverse leakage peak surge clamping temperature part (volts) (note 1) @i t (ma) v wm at vwm current i ppm voltage at i ppm coefficient number min max (volts) i d (ua) (note 2)(amps) v c ( v olts) of v br (% / o c ) 6.12 7.48 10 5.50 1000 145 10.8 0.057 6.45 7.14 10 5.80 1000 150 10.5 0.057 6.75 8.25 10 6.05 500 134 11.7 0.061 7.13 7.88 10 6.40 500 139 11.3 0.061 7.38 9.02 10 6.63 200 126 12.5 0.065 7.79 8.61 10 7.02 200 130 12.1 0.065 8.19 10.0 1.0 7.37 50 114 13.8 0.068 8.65 9.55 1.0 7.78 50 117 13.4 0.068 9.00 11.0 1.0 8.10 10 105 15.0 0.073 9.50 10.5 1.0 8.55 10 108 14.5 0.073 9.90 12.1 1.0 8.92 5.0 97 16.2 0.075 10.5 11.6 1.0 9.40 5.0 100 15.6 0.075 10.8 13.2 1.0 9.72 5.0 91 17.3 0.078 11.4 12.6 1.0 10.2 5.0 94 16.7 0.078 11.7 14.3 1.0 10.5 5.0 82 19.0 0.081 12.4 13.7 1.0 11.1 5.0 86 18.2 0.081 13.5 16.5 1.0 12.1 5.0 71 22.0 0.084 14.3 15.8 1.0 12.8 5.0 74 21.2 0.084 14.4 17.6 1.0 12.9 5.0 67 23.5 0.086 15.2 16.8 1.0 13.6 5.0 70 22.5 0.086 16.2 19.8 1.0 14.5 5.0 59 26.5 0.088 17.1 18.9 1.0 15.3 5.0 60 25.2 0.088 18.0 22.0 1.0 16.2 5.0 54 29.1 0.090 19.0 21.0 1.0 17.1 5.0 56 27.7 0.090 19.8 24.2 1.0 17.8 5.0 49 31.9 0.092 20.9 23.1 1.0 18.8 5.0 51 30.6 0.092 21.6 26.4 1.0 19.4 5.0 45 34.7 0.094 22.8 25.2 1.0 20.5 5.0 47 33.2 0.094 24.3 29.7 1.0 21.8 5.0 40 39.1 0.096 25.7 28.4 1.0 23.1 5.0 42 37.5 0.096 27.0 33.0 1.0 24.3 5.0 36 43.5 0.097 28.5 31.5 1.0 25.6 5.0 38 41.4 0.097 29.7 36.3 1.0 26.8 5.0 33 47.7 0.098 31.4 34.7 1.0 28.2 5.0 34 45.7 0.098 32.4 39.6 1.0 29.1 5.0 30 52.0 0.099 34.2 37.8 1.0 30.8 5.0 31 49.9 0.099 35.1 42.9 1.0 31.6 5.0 27 56.4 0.100 37.1 41.0 1.0 33.3 5.0 29 53.9 0.100 38.7 47.3 1.0 34.8 5.0 25 61.9 0.101 40.9 45.2 1.0 36.8 5.0 26 59.3 0.101 42.3 51.7 1.0 38.1 5.0 23 67.8 0.101 44.7 49.4 1.0 40.2 5.0 24 64.8 0.101 45.9 56.1 1.0 41.3 5.0 21 73.5 0.102 48.5 53.6 1.0 43.6 5.0 22 70.1 0.102 50.4 61.8 1.0 45.4 5.0 19 80.5 0.103 53.2 58.8 1.0 47.8 5.0 20 77.0 0.103 55.8 68.2 1.0 50.2 5.0 17 89.0 0.104 58.9 65.1 1.0 53.0 5.0 18 85.0 0.104 61.2 74.8 1.0 55.1 5.0 16 98.0 0.104 64.6 71.4 1.0 58.1 5.0 17 92.0 0.104 67.5 82.5 1.0 60.7 5.0 14 108.0 0.105 71.3 78.8 1.0 64.1 5.0 15 103.0 0.105 73.8 90.2 1.0 66.4 5.0 13 118.0 0.105 77.9 86.1 1.0 70.1 5.0 13.9 113.0 0.105 81.9 100.0 1.0 73.7 5.0 12 131.0 0.106 86.5 95.50 1.0 77.8 5.0 12.6 125.0 0.106 smcg series 1500 watts surface mount transient voltage suppressor smcg 6.8 smcg 6.8a smcg 7.5 smcg 7.5a smcg 8.2 smcg 8.2a smcg 9.1 smcg 9.1a smcg 10 smcg 10a smcg 11 smcg 11a smcg 12 smcg 12a smcg 13 smcg 13a smcg 15 smcg 15a smcg 16 smcg 16a smcg 18 smcg 18a smcg 20 smcg 20a smcg 22 smcg 22a smcg 24 smcg 24a smc g27 smcg 27a smcg 30 smcg 30a smcg 33 smcg 33a smcg 36 smcg 36a smcg 39 smcg 39a smcg 43 smcg 43a smcg 47 smcg 47a smcg 51 smcg 51a smcg 56 smcg 56a smcg 62 smcg 62a smcg 68 smcg 68a smcg 75 smcg 75a smcg 82 smcg 82a smcg 91 smcg 91a http://www.luguang.cn mail:lge@luguang.cn
- 545 - electrical characteristics ( ta=25 o c unless otherwise noted ) breakdown voltage stand-off maximum maximum maximum maximum general v br test current voltage reverse leakage peak surge clamping temperature part (volts) (note 1) @i t (ma) v wm at vwm current i ppm voltage at i ppm coefficient number min max (volts) i d (ua) (note 2)(amps) v c ( v olts) of v br (% / o c ) 90.0 110.0 1.0 81.0 5.0 10.9 144.0 0.106 95.0 105.0 1.0 85.5 5.0 11.4 137.0 0.106 99.0 121.0 1.0 89.2 5.0 9.9 158.0 0.107 105.0 116.0 1.0 94.0 5.0 10.3 152.0 0.107 108.0 132.0 1.0 97.2 5.0 9.1 173.0 0.107 114.0 126.0 1.0 102.0 5.0 9.5 165.0 0.107 117.0 143.0 1.0 106.0 5.0 8.4 187.0 0.107 124.0 137.0 1.0 111.0 5.0 8.7 179.0 0.107 135.0 165.0 1.0 121.0 5.0 7.3 215.0 0.108 143.0 158.0 1.0 128.0 5.0 7.6 207.0 0.108 144.0 176.0 1.0 130.0 5.0 6.8 230.0 0.108 152.0 168.0 1.0 136.0 5.0 7.1 219.0 0.108 153.0 187.0 1.0 138.0 5.0 6.4 244.0 0.108 162.0 179.0 1.0 145.0 5.0 6.7 234.0 0.108 162.0 198.0 1.0 146.0 5.0 6.1 258.0 0.108 171.0 189.0 1.0 154.0 5.0 6.4 246.0 0.108 180.0 220.0 1.0 162.0 5.0 5.4 287.0 0.108 190.0 210.0 1.0 171.0 5.0 5.7 274.0 0.108 notes: 1. v br measured after i t applied for 300us, i t =square wave pulse or equivalent. 2. surge current waveform per figure 3 and derate per figure 2. 3. for bipolar types having v wm of 10 volts and under, the i d limit is doubled. 4. for bidirectional use c or ca suffix for types 1.5smc 6.8 through 1.5smc200a. 5. all terms and symbols are consistent with ansi/ieee c62.35. smcg series 1500 watts surface mount transient voltage suppressor smcg 100 smcg 100a smcg 110 smcg 110a smcg 120 smcg 120a smcg 130 smcg 130a smcg 150 smcg 150a smcg 160 smcg 160a smcg 170 smcg 170a smcg 180 smcg 180a smcg 200 smcg 200a http://www.luguang.cn mail:lge@luguang.cn
|
